Showing posts with label miscellaneous. Show all posts
Showing posts with label miscellaneous. Show all posts

Kitchen drawer divider becomes iPhone 4 car clip


Materials: 1 Rationell drawer divider set, 1 T'nB iPhone car kit, Warm glue, disc cutter, model kit paint (anthracite, black, ...), 1 business card, strong rubber bands, small piece of black fabric or felt, an afternoon of time

Description: This hack started out as an attempt to create a minimalistic iPhone 4 clip for my car because I was tired of the ugly and fat T'nB holder.

Step 1: Keep only the 2 vent clips of the T'nB holder.

Step 2: Take the plastic clip sides of 2 of the small intersections of the Rationell set (this takes the most effort of the whole hack) and cut them in half, keeping the straight clip sides. Trim the inner bits as far back as possible.


Step 3: Put both clips on opposite side of the iPhone 4 protecting it with a business card. Use rubber bands to keep them in to place. Notice the space between the 2 pieces. This is important to keep the clip flexible!


Step 4: Fill the back of the pieces with hot glue from a glue gun until slightly overfilled. (The glue shrinks when cooling down, which is perfect for setting tension.)

Step 5: Allow to cool down on your iPhone until the glue is no longer transparent.

Step 6: Trim the round bits of the 2 T'nB vent clips to fit in between the 2 trimmed back internal pieces of the Rationell clips (try fitting them as on the images, it will not work. Trim as much necessary.)


Step 7: Use a soldering iron to soften the glue where the clips should fit and push them in. Use the soldering iron to smoothen the glue surface. Allow to cool down.

Step 8: Glue some fabric to the inside of the clip. I used 1mm thick felt and scraped/burned off half of the thickness because 1/2 mm is enough.



Step 9: Paint the clip with model kit paint to match the colour of your car dash. I used anthracite.

Done.

My iPhone clip fits my dashboard vent perfectly. The iPhone cannot fall trough because the tension of the shrunk glue and flexibility is perfect and is kept in by the volume buttons as an extra security.


I like mine.
Have fun!

I've added a link to a gallery with all images.

~  Steven Pauwels (aka @stenito), Belgium

The Frost(a) Sledge


Materials:
Two Frosta Stools

Description: Needing a quick sledge we dismantled some well used Frosta stools and reassembled them after some hacking into a great sledge. Standard tools required and two hours on the kitchen table...


~ jonathan morris, London UK

Custom painted Snudda


Materials: Snudda lazy susan, acrylic paint and urethane finish

Description: My inner 1950's mom came out and I purchased the Snudda about a year and a half ago. I wanted to paint it and do something, but needed some time to think. After being held hostage for a week in the snow I painted. I decide to draw upon the scandanavian prints that I'd seen before and create a chaotic, whimsical piece that quite possibly only a mother could love.


The Snudda required sanding to get the basic finish off and several coats of acrylic paint to get the saturation just right. After it dried I sealed it with a urethane finish since it would come in contact with liquid and kids. That was that.

See more of the hand painted Snudda.

~ Annie Page, Indiana

24 Karat Knob


Materials: Ikea Knubbe Wood Knob for Doors or Chests , Kommodes or Drawers

Description: I made the pure Wood Knob with Chalk and Glue often, 2- 3 Times. After drying i put some Öl on it. After this i gild it with Goldplates 24 Karat Gold.


~ Melanie, Hamburg

Gåsgrunda Pengel Stove


Materials: Trashbasket + Toothbrush Gasket

Description: This is my Gåsgrunda Pengel Stove,

Its made out of 2 products from IKEA. 
The Gåsgrunda Trashbasket
The Gåsgrunda Toothbrush Gasket

This one is very handy and reliable for all the Hackers out there.

Following equipment is needed:
1 Gåsgrunda Trashbasket
1 Gåsgrunda Toothbrush Gasket
1 Drill (for Iron) 5mm
1 Drill (for Iron) 7mm
1 Drill (for Iron) 10mm
4 Stainless Steel Brackets
8 Screws
8 Nuts

1) Drill randomly approx. 15x 5mm holes at the bottom of the Toothbrush Gasket

2) Drill 8x holes (7mm) at lower part of the Toothbrush Gasket. (Approximately 20mm above the bottom)

3) Drill 8x 10mm holes at lower part of the Trashbasket. Distance between the holes should be even.


4) Place the Toothbrush. Gasket to the backside of the lid from the Trashbasket.
The Toothbrush Gasket should be placed in the center of the lid. (Backside= is that side that faces down when the lid is placed on top)

5) Place the Brackets and mark on the backside of the lid for drilling.

6) Drill 4x 5mm holes

7) Mount the Brackets and place the Toothbrush Gasket to mark the second attachment of the Brackets.(At the side of the Toothbrush Gasket)

8) Drill holes (5mm)

9) Mount the Brackets now to the side of the Toothb. Gask.

10) Drill 2 holes in between every brackets (7mm). Approx 20mm from the top.

Now, assemble / place the Lid with the mounted Toothbrush Gasket into the Trashbasket
and your Gåsgrunda Pengel Stove is ready to be used.
No extra sealing is needed!
Please have in mind that this is a very strong Stove, it is also a very strong material.
Please be careful once you drill, since it can be somewhat "slippery".

For a clearer idea, please watch this video:


~ Håkan, Sweden

Lack with an ironing secret


Materials: Lack shelf, antique ironing board top, ironing board cover, 2 shelves from "as is" department, 2 bookends, graduated blocks of wood, black lacquer paint, L brackets

Description: I don't like setting up an ironing board and don't like the pull-down models, yet didn't have more than 10 inches clearance on the wall next to my small laundry center.

I found a Lack shelf still in plastic at the PTA thrift shop and, as it was the right size to fit in the space, decided to use it to hide an ironing board.


I found an antique wooden ironing board top made with one center board and two narrow side pieces. I pried off one of the side pieces and cut off the end to yield an ironing board top that would fit under the Lack shelf. I trimmed an ironing board cover and stapled it on the ironing board.

To make legs for the ironing board, I used L brackets to attach shelves to the bottom of the board at an angle. The shelves were from the "as is" department and originally from an unidentified Ikea item. The item is apparently graduated because the shelves' fronts are on a slant, which though not something I planned for works well with the design. I then mounted the Lack shelf to the wall just above the top of the ironing board.

To stabilize the legs I attached wooden bookends to the back of the legs at the bottom and graduated blocks of wood to the front, all painted with black lacquer.

When I need to iron, I pull the board out from under the Lack shelf and slide it over next to the dryer. I keep my iron on top of the dryer to make the set-up all the more handy.

~ Bess, Chapel Hill, NC

A woody radiator cover


Materials: MOLGER storage stool, Shelf from As-Is section

Description: We are new to IKEA hacking.

Our curious little 1 year old was sure to burn herself on our dangerously hot radiators in our rental apartment. It is apparently NOT the landlord's job to make these safe. Thus, we set out to buy radiator covers, but I REFUSED to fork out hundreds of dollars (a piece) for two custom-made radiator covers for a RENTAL that we probably were going to leave at the end of our current lease. So this is what came of my stubborn frugality.


WE had a MOLGER stool, and I liked the look. I disassembled the stool. The slatted pieces that made the four sides of the stool were used as the front of the cover and allow for airflow. I then bought a couple pieces of wood to make the sides. I had to measure for the height that I wanted. This radiator cover doubles as a side table next to our couch. I checked the as-is section for a nice looking shelf for the top.

I put the slatted front together first. There are two shapes that come out of the MOLGER stool, one has two legs (U-shape) and one is just a square piece with slats. The piece without legs can be snugly fit in-between the legs to create one long slatted piece. I used tacks to secure the two pieces together. I needed to use a whole Molger M stool and a board from the hardware store in the middle to get the width we needed. Then we just hammered it together with skinny nails. Hammered the sides and top onto that. Hindsight, we should have put a layer of wood glue in-between pieces before nailing. It was an easy hack since a radiator cover is just a three-sided box with some sort of airflow. IT WORKS AMAZINGLY and is actually attractive. Probably someone with more patience or skill would use something more sophisticated than nails, but we are cheap and impatient.


Check the pictures for more details. You will notice the little plastic circles - these are the "bottoms" of what were the legs of the MOLGER stool. They come assembled with these little plastic skid stoppers. We just left 'em on.

~ Jojo, NYC

RIBBA Dataport


Materials: RIBBA, Pine boards, black paper

Description: Take a slightly thicker frame type RIBBA, a few bars and construct a box:
The add a back to the frame with black paper and screw on the electronics.
Then, the front passepartout with it and end up with a cardboard tube from wrapping paper serves as a cable channel.


See more of the Ribba Dataport.

~ Andreas K., Germany

Fireplace: Frump to Fab!


Materials: Nexus YB cabinet and drawer fronts; tape measure, paper, tape, power drill, jig saw

Description: Our 1950s house came with a very frumpy fireplace in the living room. Even before we had unpacked, I started demolishing the mint green paneling, the rickety DIY shelving and the shiny brass fireplace insert! My original plan was to cover it with faux limestone for a chic, mod look but when that proved to be too expensive, I realized I'd been collecting the perfect material already: Nexus Yellow-Brown door and drawer panels from the As Is department of IKEA.


Click to read more>>

Tertial lamp into microphone stand


Materials: TERTIAL + PROEL APM 225 (or other)

Description:
Remove the bulb
Remove the power cord
Insert your Proel APM 225

~ Francesco Dosia

Ramvik arcade machine


Materials: Ramvik

Description: I made an arcade machine from an Ikea Ramvik table.

All the steps of the contruction are on my blog including video.


See more of the Ramvik arcade machine.

~ jed, Dijon, France

Earring holder


Materials: DOKUMENT letter tray

Description:
Having lots of hook earrings I was looking for somewhere to hang then cause they always get tangled into each other. I had seen the mesh system stapled into a picture frame but I didn't feel like crafting. A quick scan on my office and I found the perfect solution. Dokument on its side! The mesh is big enough to easily get earrings through yet small enough to hold studs. You could attach it direct to the wall or do as I did here and just put it on a shelf behind my other jewellery boxes, this keeps it portable and easy to reach.

~ Ingrid Mertens, Quebec Canada

Flyt Miniramp for Fingerboards


Materials: Flyt Magazine case

Description: To convert your Flyt Magazine case into a Flyt Miniramp for fingerboards

1. Take 4 Flyte magazine cases and asemble as instructed.


2. With the instruction paper mark out and cut a template as shown in the photo.


3. Mark out using the template on the flyt case and cut off the scrap area.

4. Using PVA Glue assemble the ramp as shown in the photo.


5. With the scrap card insert stiffeners and ramp tops as shown in the photo.


6. Start to add 3 layers of thick card (File dividers) for the ramp surface as shown in photos.

7. I downloaded many skateboard logo's and printed on sticker paper and cut to shape.

General Notes

The cost of the ramp is only a few dollars and a bit of imagination and can be designed to what the fingerboard skater wants.

This ramp took 3 evenings to build which is mainly due to the time taken for glue to dry before adding additional layers. The end result is a fairly sturdy ramp which should be able to take some reasonable use.

~ Phil Hibbard, Singapore

Check out this stream